If your riding lawn mower won’t start and you’re not hearing any clicking noises when you turn the key, there could be a few reasons for this problem. We always recommend to our visitors they should keep troubleshooting equipment for the primary solutions.
In this guide, we’ll troubleshoot some common issues and walk you through the steps to get your lawn mower up and running again.
You will get accurate information because we practically do it many times.
What To Do Riding Lawn Mower Won’t Start No Click?
Below are the most common reasons your riding lawn mower won’t start and how to fix them:
1. Check the battery and connections
A dead battery or poor connection could cause your lawn mower’s silence. To check this:
- Inspect the battery for any signs of damage, such as cracks or bulging
- Ensure the battery terminals are clean and corrosion-free
- If necessary, use a wire brush or sandpaper to remove any corrosion
- Verify that the cables are securely connected to the battery terminals
- Test the battery voltage with a multimeter; it should read around 12 volts
- If the battery voltage is low, charge it or consider replacing it
2. Examine the ignition switch
A faulty ignition switch may prevent your riding lawn mower from starting. To test this:
- Disconnect the spark plug wire to avoid accidentally starting the engine
- Use a multimeter to check the ignition switch for continuity
- If the switch is faulty, replace it with a new one
3. Inspect the solenoid
The solenoid transmits electrical power from the battery to the starter. To check the solenoid:
- Locate the solenoid, which is usually near the battery
- Use a jumper cable or screwdriver to create a connection between the large terminals on the solenoid (one should be connected to the battery and the other to the starter)
- If the solenoid clicks and the starter engages, the solenoid is most likely functional
- If there is still no clicking sound or starter engagement, consider replacing the solenoid
4. Check the starter motor
If you’ve ruled out the above issues, the starter motor may be faulty. To test this:
- Remove the starter motor by disconnecting the electrical connections and mounting bolts
- Carefully inspect the motor for any visible damage or wear
- Test the motor with a multimeter for continuity and voltage
- If the motor shows no signs of life, it may need to be replaced
5. Confirm safety switches are functional
Riding lawnmowers often have safety switches that prevent the engine from starting if certain conditions aren’t met (e.g., the driver isn’t seated or the blades are engaged). If these switches are faulty, they could cause a no-start situation. To check:
- Inspect each safety switch for damage, wear, or faulty connections
- Bypass each switch one at a time by disconnecting it and connecting the two terminals
- If the mower starts after bypassing a switch, that switch may be faulty and need replacement
6. Corroded Spark Plugs
Though rare, corroded spark plugs can also cause a riding mower not to start. To check the spark plugs:
- Disconnect the spark plug wires from the plugs and inspect them for any signs of corrosion or damage
- Clean off any corrosion with a wire brush or sandpaper
- Replace any damaged or corroded spark plugs
7. Fuel Issues
If all the above tests check out, it’s likely a fuel issue. To determine if this is the cause of your mower’s silence:
- Check the fuel filter and replace or clean it as needed
- Inspect the fuel lines for cracks or other signs of damage and replace any faulty ones
- Verify that there is fresh gasoline in the tank and clean off any dirt or debris from the fuel cap
- Test the spark plugs for a spark; if there is none, it may indicate a fuel issue
- Check the carburetor and clean out any clogs
After examining and addressing these potential issues, reconnect the spark plug wire and try starting your lawn mower once again. Hopefully, one of these troubleshooting steps helped you get your riding lawn mower back up and running.
Consider having a professional inspect your riding lawn mower if all else fails. They will be able to diagnose and fix any issues you cannot identify. With proper maintenance, your riding mower can provide years of reliable service.
Why My John Deere won’t start No clicks?
A dead battery or faulty ignition switch could be why your John Deere won’t start any clicks. Check the battery, ensure the connections are clean, inspect the switch for continuity, and bypass any safety switches as needed. If all else fails, consider taking it to a professional for repair.
Why does my riding lawn tractor click but won’t start?
A few issues, such as a faulty ignition switch, battery, or solenoid, could cause this. Try troubleshooting these components and replacing any defective ones to see if it resolves the issue.
What should I do if my lawn mower won’t start with a new battery?
If you’ve recently replaced your lawn mower’s battery, but it still won’t start, another issue could be causing it. Try checking the ignition switch, solenoid, and starter motor to see if they are defective or need replacement.
My tractor won’t start no click; what should I do?
If your tractor doesn’t start with no click, a few potential issues could be causing the problem. Check the battery and connections, examine the ignition switch for continuity, inspect the solenoid for engagement, test the starter motor, confirm safety switches are functional, check for corroded spark plugs, and examine fuel lines for damage.
Riding a lawn mower won t start no clicking can be challenging to diagnose and repair. In this guide, we walked you through some common issues that could cause your mower not to create and the steps you need to take to get it running again.
If all else fails, consider taking it in for service by a professional. Your lawn mower should provide years of reliable service with proper maintenance and care.
Douglas Mackalie is a Founder of Mackalies Garden. He is one of the most exciting people you’ll ever meet. He has 25 years of experience in horticulture and gardening, most of which he’s spent outdoors getting his hands dirty.