10 Common Troy Bilt Zero-Turn Mower Problems + Troubleshooting Solution

If you’re the proud owner of a Troy Bilt zero-turn mower, then you know how great they can be for quickly and easily getting the job done.

However, even the best machines sometimes experience problems. In this article, we’ll look at some of the most common Troy Bilt zero-turn mower problems and provide troubleshooting solutions to help you get your device back up and running in no time.

Common troy bilt zero turn problems can be associated with a spark plug, blades, fluid, air, oil filter, and transmission problems. Let’s have a look at the following points:

10 Common Troy Bilt Zero-Turn Mower Problems

1: Mower Won’t Start

If your Troy Bilt mower doesn’t start, there are a few possible culprits.

One of the most typical reasons is that the mower is not getting enough electrical current.

It could be due to a problem with the ignition switch, the battery, or another electrical system component.

Another common reason for a mower not starting is an airflow obstruction. It could be caused by a clogged air filter or a blockage in the exhaust system.

Finally, if your mower has a gas engine, ensure enough fuel is in the tank. If the tank is empty, the mower will not start.

How to Fix It.
  • Check out the gas tank and fill it up if it’s empty.
  • If your mower has an electric starter, ensure the battery is fully charged.
  • If your mower has a pull starter, check if the cord is stuck or damaged.
  • Finally, if you suspect an electrical problem, take the mower to a qualified technician for diagnosis and repair.

2: Starts Then Stops

Another common issue with Troy Bilt mowers is that they start but stop after a few seconds.

Several issues, including a spark plug, a problem with the engine oil, or an air filter, can cause this.

How to Fix It:
  • If your mower starts but then stops, you should first check the spark plug.
  • If the spark plug is dirty or damaged, it must be replaced.
  • Next, check the oil level in the engine. If the oil is low, add more oil until it reaches the whole line on the dipstick.
  • Finally, check the air filter and clean or replace it if it is dirty.

3: Mower Stops While Mowing

When the mower is running, there’s no problem. But if it suddenly stops while you’re mowing, there could be several reasons. An overheated engine might cause your Troy Bilt mower to quit while you’re in the middle of it. lawnmowers can also stop if there’s a problem with the carburetor, fuel tank, or air filter. This is a general troy-bilt riding mower transmission problem.

How to Fix It: 

If your mower stops while you’re mowing, you should first check the engine. If the engine is overheating, stop mowing and let it cool down for 30 minutes. Next, check the carburetor and clean it if it’s dirty.

4: Troy bilt riding mower transmission problems:

You may experience some common troy bilt zero-turn hydrostatic transmission problems while mowing. These include leaking fluid, difficulty moving the mower, and the mower stopping unexpectedly.

How to Fix Troy bilt hydrostatic transmission problems: 

When mower leaks fluid, it’s probably due to a seal or gasket that needs replacing. If the mower has trouble moving, ensure the transmission fluid is at the correct level. If the fluid is low, add more until it reaches the whole line on the dipstick. Finally, if the mower stops unexpectedly, check the brake pads and replace them if they are worn.

5: Mower Can’t Drive Correctly

Another troy-bilt zero-turn mower problem is having trouble driving in a straight line or turning; there could be an issue with the wheels. The wheel alignment might be off, or the tires might be inflated to the incorrect pressure.

How to Fix It: 

The first thing you should do is check the tire pressure. If the tires are inflated to the incorrect pressure, they will cause the mower to drive erratically. Next, check the wheel alignment. If the wheels are not aligned properly, they will also cause the mower to drive erratically. Finally, if the problem persists, take the mower to a well-qualified technician for diagnosis and repair.

6: Mower Won’t Move

The following are the most common causes: 

  • worn-out mower components,
  • an engaged drive release lever,
  • and a lack of hydraulic oil.
How to Fix It:

Check the brand manual to see how to disengage the drive release lever.

7: Troy-bilt mower deck problems (shakes and vibrates)

The following are the most common causes: 

  • a dull blade,
  • uneven ground,
  • and a loose deck.
How to Fix It:

Check the blade to see if it requires to be sharpened or replaced.

Check for any unevenness in the ground, and make sure the deck is secure.

8: Uneven Cutting Problem

If your Troy Bilt zero-turn mower is leaving behind patchy or uneven grass clippings, the problem could be with the blade. Start by checking to see if the blade is dull or damaged.

If so, you’ll need to replace it. Another possible cause of this problem is an issue with the mower deck. If the deck is levelled, it can prevent the blades from cutting unevenly.

How to Fix It:
  • To fix this problem, start by checking the blades to see if they need to be replaced.
  • If the blades are in good condition, check the mower deck to ensure it is level. If the deck is not level, use the adjustment screws to level it out.
  • Finally, adjust the mower’s cutting height to see if that helps fix the problem.

9: Gas Leaking

If you notice gas leaking from your Troy Bilt zero-turn mower, the problem could be with the fuel line. This common issue is usually caused by a crack or hole in the fuel line.

How to Fix It:

Our professional landscapers recommend replacing the fuel line if you notice any gas leaking. If the issue is with the fuel tank, you may need to replace the entire tank.

10: Mower Smoking

If you notice your Troy Bilt zero-turn mower is smoking, there could be a few different issues.

One possibility is that the engine is overheating. Another option is that the oil level is too low or an oil leak.

How to Fix It:

To fix this problem, start by checking the oil level and adding oil if it is low. If the oil level is good, then check for oil leaks.

You must replace the gasket or seals if you notice any oil leaks. If the mower is still smoking, the engine is likely overheating.

In this case, you’ll need to take the mower to a professional for repair.

Maintenance Tips:

Here are some maintenance tips to follow:

  1. Always remember safety: Before cleaning, repairing, or inspecting, disconnect the spark plug and battery, and wait for all moving parts to come to a complete stop.
  2. Grass catcher components: To prevent expensive repairs, clean the inside of the mower deck and all grass catcher components regularly.
  3. Sharpen or replace blades: For a consistent cut, we recommend that you sharpen or replace the blades every 25 hours.
  4. Check oil and filters: Always check the oil level before each use, and change the oil and filter according to the manufacturer’s recommendations.
  5. Clean air filters: Clean or replace the air filter at the beginning of each mowing season or every 100 hours of use, whichever comes first.
  6. Lubricate: Lubricate the moving parts on the mower deck and all grease points every 25 hours or at the beginning of each mowing season.
  7. Tighten hardware: Check all nuts, bolts, and screws at the beginning of each season, and tighten as needed.
  8. Mulching kit: If you have a mulching kit, ensure the blades are installed correctly and the baffles are in place.
  9. Some additional lawn mower troubleshooting and maintenance tips to consider:
  • If you strike a foreign object, shut off the engine and remove the spark plug ignition wire. Thoroughly inspect the mower for any damage. Repair the damage before starting and using the mower.
  • It would help if you did not change the wheel or the cutting height when the engine is running.
  • Regularly check for cracks and leaks in the fuel line, tank, cap, and connections. If repairs are necessary, replace them.


Why Won’t My Troy Bilt Lawn Mower Stay Running?

This is a common problem with Troy Bilt lawnmowers. There are a few things that could be causing the problem.

  1. The spark plug may be dirty or faulty. Clean or replace the spark plug and try starting the mower again.
  2. The air filter may be dirty. Clean or replace the air filter and try starting the mower again.
  3. The fuel may need to be stale. Drain the old fuel from the tank and fill it with fresh fuel. Try starting the mower again.
  4. The carburettor may need to be cleaned or adjusted. Clean or adjust the carburetor and try starting the mower again.
Where Is The Fuse On A Troy Bilt Riding Lawn Mower?

The fuse on a Troy Bilt riding lawn mower is located under the dash, near the battery. The fuse box will have a diagram that shows which fuse goes to which circuit.

How Do I Adjust The Cutting Height On A Troy Bilt Lawn Mower?

To adjust the cutting height on a Troy Bilt lawn mower, adjust the levers on the side of the deck. The levers are marked with numbers that correspond to the cutting height. For example, if you want to raise the cutting height, move the levers to a higher number.

How to Troubleshoot Troy bilt riding mower transmission problems?

If you are experiencing troy bilt hydrostatic drive problems, there are a few things you can do to troubleshoot the problem.

  1. Check the oil level in the transmission.
  2. Check the transmission filter. If it is dirty, replace it with a new filter.
  3. Check the transmission belt. If it is loose, adjust it according to the manufacturer’s instructions.
  4. If the problem persists, take the mower to a qualified repair shop for further diagnosis and repair.
Why is Troy bilt Bronco better than troy bit pony?

Due to Troy Bilt hydrostatic drive problems, Troy Bilt bronco is better than troy bit pony. I suggest spending $100 more and buying the Bronco 42X Riding Lawn Tractor with an automatic transmission.

What tools are needed for Troy Bilt lawn mower troubleshooting?

To effectively troubleshoot your Troy Bilt lawn mower, you’ll need a few essential tools:

  • A clean, dry cloth or paper towel
  • A small Phillips head screwdriver
  • A can of compressed air

You may also need a pair of needle-nose pliers.


Your Troy-Bilt mower is a valuable machine that helps make yard work easier. Be sure to take care of it so it can take care of your yard year in and year out.

We hope this guide has helped you with Troy Bilt lawn mowers troubleshooting. These are the most common problems with Troy Bilt zero-turn mowers. If you have any further questions, feel free to contact our professional landscaper team.

Leave a Comment